Breakdown and Carrydown – Then and Now
We hear it all the time; “the heads are hooking”, “carrydown is happening quickly today”, “time to move again”, “my ball’s burning up – grab the fire extinguisher!”...ok maybe not the last one. But with the amount of oil needed in today’s environment in order to protect the lane surface and keep the modern ball from hooking into the gutter at the arrows, rapid and chaotic change is often the result. Even the best of players can get confused in today's game over the course of a few games.
In this month’s piece we'll try and give some sense of order to that chaos, but the first thing many will have to do is let go of what you’ve learned and experienced in the past – today’s pattern mutation, carrydown, and resulting bowling environment is different, very different.
Oil Pattern Change
The first thing we need to understand about oil pattern change is how bowling balls with different amounts of track flare change the oil pattern.
Prior to the 1980’s, when bowling balls did not significantly flare, the ball essentially picked up all the oil it could within the first couple revolutions - the first 8’ to 16’ of the oil pattern. It was in the head area where the oil pattern dried out the most, and after that, the oil pattern basically remained unchanged. Only once we got to a point of about 24 games per lane or more, did the rest of the pattern began to “dry out”.
As lower flaring more aggressive coverstock balls were introduced in the mid to late 1980’s, the amount of oil on the lanes had to increase, and oil pattern mutation changed because of that. John Davis' research showed the latter half of the oil pattern actually increased in volume during this era.
Back then the bowling ball picked up so much oil in the front part of the lane, it re-deposited some of that oil towards the end of the pattern, and then a lot more of that oil on the dry back-end. This is the time when carrydown quickly became a big problem.
When ball manufactures figured out that track flare increased the friction between the ball surface and the lane surface, bowling balls became unbalanced again - only this time it was by way of significant Radius of gyration (Rg) differential, It was then, oil pattern mutation, and the resulting ball motion, changed dramatically.
However, bowler "lingo" hasn't seemed to change as much as pattern mutation has, which can cause a lot of confusion and misinformation in our world of bowling.
Bowling balls with track flare (pictured below far right) pick up and erase oil off the lane with every revolution, causing a much different type of oil pattern breakdown. It’s not just the heads that breakdown down anymore, it’s the entire length of the oil pattern that breaks down, and it begins with the first ball thrown on the oil pattern.
In our research, when starting with 80 units in the front part of the lane, our after tapes show that about half the oil has been depleted during a normal league session, which is 15 games per lane. We see the same trend in high level events bowling 12 games per lane.
That means there are still about 40 units left in the heads, but many in our industry still talk about the “heads hooking”. Anyone want to bowl on a pattern with 40 units on the outsides? Of course you don’t - your ball will never hook! So what causes the players to move left in today’s bowling environment? It’s more about the removal of oil from the mid-lane towards the end of the pattern.
Because of oil pattern taper, the mid and end part of the oil pattern has much less oil than the front part of the oil pattern. As the ball erases the oil off the lane, the modern “mountain range” like coverstock can easily poke through that thin film of oil towards the back part of the pattern. This causes the ball to read the friction much sooner there than in the front part of the pattern, and that is what makes players move left, not the oil pattern breaking down in the heads.
What this flaring ball pattern breakdown does to ball motion is simple – the ball simply slows down sooner and therefore hooks more. For high rev and high ball speed players, this pattern mutation falls right into their wheel house as finesse has been removed from the equation for them - its flat out every shot without having to worry about “throwing it through the break point”.
For rev challenged and slower ball speed players, this pattern mutation becomes more difficult to overcome – their bowling balls slow too early and begin to lose axis rotation too soon causing less room for error and decreased pin carry.
Of course this type player could switch to a less aggressive ball to combat the increased friction towards the end of the pattern, but then that type ball is more susceptible to carrydown. It’s a delicate balance for these styles of players.
Can the heads (the first 16 feet) still give the ball the perception it is hooking early? Sure they can, but in today’s bowling environment, more often than not it’s not because of the lack of oil.
With synthetic lanes it’s normally a side hill slope issue where the ball is thrown into a hill and trying to rotate up that hill. This topography issue will make the ball “check up” or move in the direction of the slope, which is more of a gravity issue, with a bit of friction thrown in for the banked curve affect.
For wood lanes or really old synthetics, it could be a severely roughed up lane surface, which therefore is a friction issue. However no reasonable amount of oil will significantly help in either of these situations simply because the depth of the scratches in the lane surface are deeper than the oil film – resurfacing or re-leveling the lane surface is the only solution to combat that kind of "early hook".
In short, bowling balls that do not flare tend to break an oil pattern down from front-to-back, and today's high flaring balls tend to break down oil patterns from back-to-front.
With high flare balls the oil pattern is literally getting shorter in the ball traffic area with every shot thrown, and by moving left we are increasing our launch angles to that area in order to give the ball more time to hook. Of course when missing inside of target, we are now in a "longer pattern" again so the ball holds pocket. This is why sport and challenge patterns get "easier" and scores often increase after a few games.
Carrydown
Carrydown is also much different by balls that don’t flare versus balls that do flare. Bowling balls that do not flare leave long three to four foot streaks of carrydown beyond the end of the pattern. Because the footprint of the bowling ball is so small, a shot hitting these long streaks of carrydown can all of a sudden make a pattern feel like it is much longer, mainly because to the bowling ball, on that single shot, the oil pattern has become longer!
With the amount in the middle of today's oil patterns, it is not uncommon for those streaks of oil to be in the 5-8 unit range.
As noted before, significant carrydown was not a problem in bowling until the 1980’s - especially towards the middle to end part of the decade. With the advent of ever stronger urethane balls, as well as increased dynamic weight blocks, an increased amount of oil was necessary as more and more customers bought these new balls.
And as players began sanding the covers and using drilling techniques to create more dynamic imbalance, more oil was needed to help protect the lane surface and keep these new higher friction balls on the lane, and of course, keep the customers who bought these new balls happy.
It was only then that we saw carrydown become such a significant part of the playing environment in so few games. Prior to that, when fairly dynamically balanced rubber and polyester balls were mainly in use, there was simply not enough oil needed nor used on the lanes to cause significant carrydown issues.
Sure there was carrydown after a few days of play, when lanes were not cleaned but once a week, but nothing like what happened in the 1980’s to tournament organizations like the PBA Tour, who cleaned the lanes every day.
Carrydown that is created with balls that flare however is much different, as well as how these much more aggressive and diverse internal dynamic balls allow players to play the lanes.
Meaning, because the amount of dynamic imbalance is much greater, this increases the range of available hook and allows players to play the lanes in a much wider area than in the past. When balls were more balanced and didn’t hook as much, everyone played the lanes near the same area, causing a much narrower spread of carrydown.
This dynamic imbalance causes track flare, and track flare creates what are called “bow ties” (where the flare rings come together) at only two points on the balls surface. Those two points are the only parts of the ball with oil on it that touches the lane every revolution.
The higher the differential Rg, the wider the track flare is, and the smaller those touching points are. This in turn creates random 2” to 3” strips of carrydown. For instance, using a 40’ pattern as an example, one track flare carrydown strip may be at 41’ to 41’ 3”, another small strip at 41’ 6” to 41’ 9”, and another one at 42’ to 42’ 3”, etc.
Therefore, when a fresh part of the modern flare balls surface comes in contact with these small strips of carrydown, ball motion is hardly affected at all. As these strips build up however, along with the longer three to four plus foot random strips of carrydown created by the many low flaring spare balls going down the lane, the back-ends will “tighten up” somewhat, but not as soon, or as much, as lanes did in the late 1980’s.
There was a very good article written by the PBA that represents what happened in the late 1980’s. It stated how after a few games of bowling the “fronts go away” and significant carrydown happens beyond the pattern at the balls exit point.
When this occurs, the player who greatly hooks the ball can move left and effectively “go around” the carrydown, creating an increased margin of area from that of a fresher oil pattern, and clean dry back ends. Low flare carrydown gives this style of player hold area inside of target.
On the PBA Tour in the mid to late 1980’s it was not uncommon for big hook ball players to average 20-30 pins a game more in the evening blocks versus the morning blocks.
Today however, even though high rev and high ball speed players can often struggle right out of the gate because their ball motion is too “skid-snappy” on the fresh, with today’s expeditious pattern breakdown, and high friction balls, high rev players can hit their stride much sooner. Today it doesn’t take more than a couple games to “smooth out” their ball motion from front to back.
In addition, as we stated before, carrydown at the end of the pattern with high flaring balls is not as defined as it was in the 1980’s, or when lower flaring urethane balls were in use. Therefore today there is simply not enough defined carrydown to go around and use as hold area.
High rev players tend to get their advantage today more from rapid pattern breakdown towards the mid and end part of the pattern, not carrydown. As most know, low to non-flaring balls today are most often regulated to shooting spares and therefore, those long strips of carrydown are more random across the lane surface - sometime you’ll hit a strip, and sometimes you won’t.
Remember, today you must think different. No longer are we using non-flaring balls on less than 5 milliliters of solvent based lane conditioner like we did in the 1970’s. No longer are we using low flaring balls on 12 milliliters of oil with massive carrydown like we did in the mid to late 1980’s. No longer are we bowling on lanes that are resurfaced every year like was mandated until deletion of the rule. No longer is levelness being maintained regularly like we did prior to advent of synthetic lanes.
The bowling environment today is much more varied, much more complex, and does not always make sense, or play “how it’s supposed to play”.
The best piece of advice we can give you is what the late great PBA National Tour tournament director Harry “Goose” Golden use to say to the players after every roll call; “bowlers, let your ball be your guide”.
JJ's Blog - 2012 Team USA Trials
Saturday December 31st
The alarm went off at 2:45 am. It was an early one but it was easy to get up because I was heading to Los Angeles and then Las Vegas to bowl the Team USA Trials. I’m an early-airport-guy so I like to be at the gate like 90-120 minutes before my flight. Since my flight was at 7:30am, that would get me to the airport to about 5:00am. I got up a little extra early just so I could go through my checklists to make sure I had everything.
I got to the airport at 5am and had a quick and painless check-in and run through security. I sat in the Delta Sky Club for about an hour and a half and then went to the gate. We boarded on time and everything was going as planned. I was supposed to get to Los Angeles at 10am and was going to spend the day shopping and also going to this cupcake place in North Hollywood that makes the best cupcakes. I wanted to share some of these with a few of my friends that were going to be bowling the tournament next week.
For those of you that don’t know me real well I have a real passion for two things: Clothes and chocolates/cookies/pastries/any kind of sweets.
We sat at the gate until about 8am when the pilot got on and said that they were having trouble with the fuel pump and they were having the mechanics come out and look at the plane so at this time we didn’t know how long it was going to take. Mind you, this plane just arrived from LA about 6:30am, so all they were doing was basically topping off the tank and cleaning it up and it was heading straight back to LA.
About 8:20am they were letting people de-plane but told them to check in to the gate every 10 minutes to make sure all was ok because when the plane was ready, we were leaving ASAP. About 8:35am the pilot said we were ready to go and at 8:45am we were all boarded. Well, 5 minutes went by, then 10 minutes, and then at 9am the pilot got back on the PA and said that the fuel pump was still not working and we were going to be re-routed because he had no idea how long this was going to take.
Next thing I knew that I was getting rerouted to Atlanta and my itinerary said I was going to get to LA about 6:40pm!
Since this was New Year’s Eve, most of the stores I wanted to shop at were going to be closed by 6 and when I called the cupcake place they were going to close around 5pm or maybe a little later depending on business and they were going to be closed on New Year’s Day, so it looked like my window for cupcakes was closing. This had all of the makings of a really bad day.
I got to Atlanta and I got on standby for the 1:20pm flight that was going to get into LA at 3:20pm. Fortunately, I got on! Things were looking up all of a sudden!
I got to LA at 3pm (even better) but since I flew on standby my luggage didn’t make it. That wasn’t a big deal since I was staying right across the street from LAX. The lady in baggage service said my bags were on the way to Salt Lake City and then LA and they should be there tonight. Well since I was there early, I got to the rental car place and off I went. I left the airport at 3:30pm and I was only about 30 minutes from the cupcake store. Since the guy I spoke to said that they were closing at 5pm, I should’ve had enough time to get a few cupcakes.
I got to the cupcake place at 4pm only to find a note on the door saying that they had already sold out of their inventory and they would be re-opening on Monday.
Happy New Year! Well isn’t that just flippin’ great! Cupcakes…..denied!
Since I was a little peeved about that I headed to Beverly Hills to do a little clothes shopping. It was about 25 minutes from North Hollywood to the “Hills”. I stopped at this one store on Melrose Avenue and looked around but found nothing I liked despite the sale that was going on. I then headed off to Rodeo Drive and got there right at 5pm. With my good fortune continuing, I found out that all of the stores on Rodeo closed at 5pm on New Year’s Eve as well as Neiman Marcus on Wilshire Blvd., the one department store I REALLY wanted to see today. Stay Hot!
Fortunately Saks Fifth Avenue and Barneys New York were still open as they weren’t closing until 7pm. I spent about a little more than an hour shopping at both stores, but still found nothing I liked. This was turning into a really bad day. What made it worse is Rodeo Drive is also closed on New Year’s Day. I found that out last year as the Team Trials were basically on the same week and I flew out New Year’s Day last year just to find out Rodeo Drive was shut down. So far, no cupcakes for me or my friends and only about 15% of the shopping done that I wanted to get done. This day has definitely been “no bueno” so far.
Being now about 6:30pm and being quite hungry I grabbed a quick bite at the Grill on the Alley and went to go check into the room. I first had to go back to the rental car facility because when I looked closer at my rental agreement they screwed up the coupon I was using for a free day at the end of the rental. It just keeps getting better.
After clearing up that mess, I got to the hotel about 7:15pm and my luggage still hadn’t arrived. Stay red hot!
The one thing that I did have to look forward to was my good friend Missy Parkin invited me to a New Year’s Eve party hosted by her friend Scott Norton at his mother’s house. After the day I’ve had so far, I really needed something to go right considering I was denied cupcakes, didn’t do hardly any shopping and didn’t have any luggage. I didn’t want to sit in the room and think about how the day went, so I got showered and headed to their party which was about an hour from my hotel. I got there about 8:45pm and stayed until about 12:30am. I had a GREAT time as we talked, played some Password and ate some really good food. I got back to the hotel about 1:30am and lo and behold my luggage arrived! Woo-hoo! Things finally were looking up today. Well actually it was already Sunday, but it was a good way to sleep on a high note.
Sunday January 1st
I headed out about 8am to the Desert Hills Premium Outlets. It was about a 2 hour drive from LAX since the outlets were over near Palm Springs. I got there with no problems but I spent an hour there and still found nothing I liked. The bad part was the one store that I REALLY wanted to go see…….closed…..permanently. So far I was 0 for 3 on the shopping establishments, however I did get a nice ice cream cone at Haagen-Dazs which helped relieve some of my retail distress.
Since I found nothing there I made the 4 ½ hour trek to Vegas since practice session was on Monday. I was going to stop at the Outlets at Primm, NV but when I got there I figured that would be a really BAD idea.
Being New Year’s Day and around 3pm at this time, a lot of the people from LA who drove to Vegas for New Year’s Eve were heading home…….I mean…….A LOT of people were heading home. I could see at times on the southbound lanes on I-15 there were stretches where the traffic was backed up for miles. As I got closer to the exit for Primm where the outlets were at, I could see all the cars backed up on the road underneath the overpass and how they were backed up at the couple of gas stations on the southeastern corner of the exit ramp. I realized this would be a bad idea if I tried to get off so I kept going.
When I passed the overpass for the exit I noticed the southbound exit ramp (as well as the other three lanes) was backed up for about a mile and a half. It was a good call on my part since it probably would’ve taken me an extra 15 minutes to get in and probably another 20 minutes to get out, however that made me 0 for 4 on shopping. I hope the bowling goes better because the shopping has pretty much sucked so far.
I went straight to the City Center and looked around and then went to the Fashion Show Mall and then to the Forum Shops at Caesars’ Palace. I did find a nice shirt at the Forum Shops and a nice tie at the Fashion Show Mall. The shirt and tie were 60% and 70% off respectively so it was a big score to end the day. After grabbing a bite to eat at one of my favorite restaurants in the Forum Shops (Spago), I headed to Texas Station to go check into the room and call it a night.
Monday January 2nd
I woke up about 7am and spent a little time riding the stationary bike at the hotel because my right hamstring was a little tight. I felt it the night before at the end of the day and I thought if I slept on it, it would be a little better in the morning. Well……I was wrong. After about 30 minutes on the bike I felt a little better, so I went out to Panera Bread and got some breakfast. I noticed there was a cupcake store in the same plaza that Panera was in. They opened in like 15 minutes so I stuck around and grabbed a couple. They were pretty good. The day was starting off pretty well.
I came back to the room about 8:30am and then took a shower. I then left about 9:30am with Jessica Baker to go pick up Diandra Asbaty and her son Madden at the airport who was getting in about 10:30am. I made a quick stop to the Forum Shops on the way to pick up some unbelievable chocolate chip cookies at a restaurant called Max Brenner’s that I discovered the night before and then we went to go pick up Dee.
After picking her and Madden up I then made a quick trip to my good friend David Haynes’ pro shop to pick up a case of balls I had shipped there (Thanks Dave!) and then headed back to Texas Station to get ready for the one and a half hour practice session.
The practice session went well but the 90 minutes went really quick. Texas Station is 60 lanes and since we were bowling on 4 patterns over the next 4 days, they had all the patterns spread throughout the center in blocks of 14-16 lanes.
When you’ve got 13 bowling balls with you for all different patterns and you’re trying to practice on all of the patterns, it takes a little bit of time just switching bowling balls from one bag to another and then walking to one end of the house and then back to get bowling balls for another pattern and then walking back, etc. You lose quite a few minutes of practice session just walking back and forth in a 60 lane center and switching equipment from one bag to another.
I felt pretty good on all of the patterns though. Afterward we had orientation and then I went back to the Strip for some shopping and some food. Tonight was back to City Center where I had a nice Mushroom Pizza at Wolfgang Puck’s Cucina at the Crystals Mall. I found a couple of shirts I liked but they didn’t have my size, so that made me at about 2 for 7 now on shopping malls. I’m only batting a little under .300, but not too bad. At least that’s good on my wallet. The tournament begins tomorrow so I headed back to the room about 9pm and was out by 10pm.
Tuesday January 3rd
Today the tournament begins. We are going to be bowling on the 39’ Seoul pattern. This week we’re bowling on all WTBA patterns.
The pattern schedule will be as follows:
Tuesday: 39’ Seoul
Wednesday: 47’ Paris
Thursday: 34’ Stockholm
Friday: 45’ Mexico City
The Team USA Trials is also a little different this year in a couple of ways. First, we’re only bowling 7 games a day instead of last year’s 9. Also, this year’s champion will be determined by points and not total pinfall. Basically if you lead the squad by total pins, you get one point. If you’re second in total pinfall you get 2 points. If you’re third you get three points and so on down the line.
So, the person with the LEAST amount of points over 4 days is the Team USA Trials champion, the 2nd least amount of points is 2nd, and so on. It’s supposed to reward the player who is the most consistent on all 4 days which is definitely a trait of a great bowler: Versatility. The player who is really good at one pattern but mediocre/sub-par on another will definitely stick out in this format.
The day really wasn’t a real good day. My ball roll didn’t really match up too well and I was slow on reading a few transitions. Texas Station has a little more early hook than the lanes at Sunset Station (which has hosted the Team USA Trials for the last 3 years). Since my ball roll reads the fronts a lot naturally, this isn’t a real good combination for good ball motion when they break down, which started for me in game 3. I felt like I threw the ball well overall, but being a little behind on transitions kind of hurt me. I thought the scoring pace was going to be a little lower so I wasn’t quite as aggressive when I had to move inside the track and needed to start opening up the lane a little more. I was trying to “trap” the ball just inside the track from games 3-5 instead of just moving deeper and really trying to open it up. I only went +68 for 7 games which put me in 39th place for the day, especially not good considering I was +72 for the first 2 games.
I figured one point for every year that I’m old will not be acceptable for the rest of the tournament. I was kind of depressed as I wasn’t sure I’d be able to make up that many points considering this is the first time they’ve used this points system. I went back to the Forum Shops and drowned my sorrows on another Smoked Salmon Pizza at Spago and more cookies at Max Brenner’s. I knew though……..tomorrow was going to be new day.
Wednesday January 4th
Today we were bowling on the 47’ Paris. I started out the first game with a pretty good line to the pocket but I think my ball was still burning up a little quick and not getting into a roll down the lanes as I never missed the pocket for 218. I think the Rapid Fire Pearl I was using was probably flaring a little too much combined with my ball roll reading the fronts too much. I tried switching balls to an Anarchy and that wasn’t much better ball motion-wise though I did manage to shoot 230 somehow. I then switched to a Mission X in game 3 and since that flared a little less but still had a strong cover it got through the fronts and rolled through the pins much better. Now I was able to do some striking.
From here I was just trying to chase it left and stay ahead of the moves. The 6th game I was getting a little too deep as I was starting to get the big wet-dry from side to side as I was shooting a 200 game which wasn’t very good with par being around 225. I tried to move back right on the fill ball and use loft so I could keep the ball on line as I knew that if I stayed where I was at I was only going to shoot another 200 game which wasn’t going to cut it at the scoring pace that was set. It looked like it would work based on the fill ball, I just needed to move a little farther left with the same Mission X. Lo and behold, it worked! 268 to finish the day!
That put me at 7th place for the day which moved me up from 39th to 16th in the standings. Things were looking up for tomorrow for the short pattern, which has either been really good or really bad for me the last few years in this tournament.
Went back to the Crystals Mall at City Center and grabbed a pizza and some chocolates to take back for later. I then went to use Kaitlin Mayall’s ball spinner to do some ball work (Thanks Kaitlin!) and then called it a night.
Thursday January 5th
I brought two urethane balls with me to combat the short. I figured if anything it will give me more control and get me around the pocket until I see how the scoring pace is going to be and then go from there. It sounded like a solid game plan going in.......however……..then we started bowling, haha!
I think the combination of the early roll of the urethane balls, the early hook built into the surface and my roll which reads the fronts too much as it is…..was a bad combination. I shot 203 the first game which wasn’t terrible but not up to pace. I had trouble keeping it on line when I went direct but the ball had trouble cornering when I gave it some room.
After 4 frames of the next game only hitting the pocket twice with one open, I realized that urethane wasn’t cutting it. Since the loft worked out really well the last game yesterday, I thought I’d try that again. It made sense since it would help eliminate some of the early roll my release naturally gets since the ball won’t hook in the air, haha!
I switched to pretty strong bowling balls and between the same Mission X and Rapid Fire Pearl I used yesterday, I shot +204 the last 5 to vault me to 6th place in the standings for the day which shot me to 4th place overall.
It was a good day so it was time to back to the Strip at the Forum Shops at Caesars. I went with my good friend Katie Thornton to have a meal at the Cheesecake Factory and more of those good cookies at Max Brenner's and walked over to the Bellagio and bought some really good pastries at the Jean Philippe Patisserie. I brought those back to the hotel and Katie and I shared the pastries with Kaitlin Mayall and her Dad while she let me use her ball spinner again (Thanks again Kaitlin!) to prepare surfaces for the Mexico City pattern the next day.
Friday January 6th
This pattern is on paper one of the most difficult in the WTBA series. It has the potential to be pretty ugly so I felt like I kind of needed to play smart on the fresh and not try to “swing for the fences” so to speak. I was fortunate shooting 256 the first game out of the box. I threw a Red Mission playing between 10-13 really straight and had a good look. I also had the good fortune of tripping a 2-pin, a Brooklyn and a “trip 3-9” for a 5-bagger, but I took every one of them because goodness knows I might need them later. Sadly, I was really going to need them later.
I shot 196 the next game which I was still in good shape but as we made the turn to the low end I could see that there actually was some ball reaction developing between 20 and 25. After 4 frames of really bad ball reaction (and seeing some strikes from a fair amount of other people) I knew it was time to move inside. I went to the Mission X and it was the right ball but it took me a few frames to get lined up and combining that with another open frame I shot 176. I got lined up and shot 223 the next game but the next few games were a struggle. I was slipping on the approach which was resulting in a half a game of adjusting slide soles and heels and I was also seeing that my ball roll really wasn’t right.
I’m a fair amount up the back of the ball and I see that I needed more tilt and more rotation but with a softer hand. All the guys that were bowling well had that. I can get more rotation, but my tilt is still low so that makes my ball read earlier which forces me farther left which is part of the problem since I’m already about 5 boards too far left to begin with. I can get more tilt, but not with a soft enough hand. My ball roll forces me farther left (because it rolls sooner) so I get less hold when I miss in and when I get it to the right (since it burns up earlier) it doesn’t roll through the pins the right way thus it doesn’t strike as much. I’ve been fighting this all week, but it was magnified today on this pattern.
It was a disappointing way to finish with (2) 170 games in the last 3 games and that put me 35th for the day and 6th place overall. From here I needed to get picked for the Team since only the top 3 spots were automatically on the Team.
Fortunately, I got picked but I realized that I needed to work on developing this softer hand with more rotation and more tilt. That’s going to be one of the first things I’ll be working on when I get home. We had Team USA Orientation that night and then I went to get a bite to eat afterward even though it was near 10pm at that point. Overall, it was a week with some ups and downs but in the end it all turned out good. Looking forward to a good year on Team USA!
Saturday January 7th
I took Diandra, her son Madden, Jessica Baker and Jazreel Tan to the airport in the morning and then it was back to the hotel to check out and then back to Los Angeles for a couple of days of R & R. I met with Missy Parkin for lunch at South Coast Plaza in Costa Mesa (nice call on the fish tacos at Wahoo’s!) and then went to Beverly Hills for some shopping on Rodeo. I didn’t buy anything at either place, but it was just good to walk around and relax. It was a reasonably low-stress day ending with a nice juicy “Double-Double” cheeseburger at In-N-Out.
Sunday January 8th
I met up with my cousin who lives in Santa Monica in the morning and we spent most of the day together with her and her boyfriend. We did some shopping and lunch at the 3rd Street Promenade, watched the NFL playoff games at their house and then went to a few cupcake stores that were right nearby. Los Angeles is big on cupcake stores….my kind of town.
Speaking about cupcakes, I wanted to go back to the cupcake store that I wanted to go to originally the weekend before that closed early. I saw on their website that they were open until 8pm on Sunday. I thought to myself……Perfect! I’ll get there about 6pm and I’ll get some cupcakes to bring back. I said goodbye to my cousin about 5:45pm and then got to the cupcake store in North Hollywood about 6:15pm.
I get there…….and they’re closed! There’s a sign on the door saying that they close at 6pm on Sunday, but their freaking website says they’re open until 8pm on Sunday.
Ironically, this trip ended the exact way it started. Fortunately I bought a few cupcakes from one of the other stores in Santa Monica so I had some cupcakes to take home for my friends, but not the ones I REALLY wanted. It was then off to the airport to catch the 10:50pm red-eye flight and back to work on Monday morning.
At least the bowling part went well. :-)))
Fine Tuning your House League Pattern
This is the time of year when new seasons have begun and pattern decisions are being put to the test. You’ve made your choice, laid out the pattern, and now things aren’t going exactly as planned. You’ve verified that your machine is in perfect working order, now what do you do?
Once the bowlers take to the lane, lots of problems can come to light. If a majority of your bowlers are experiencing the same problem, it may be time to make adjustments to the pattern. Common complaints could be: too much carrydown, back ends too strong, not enough hold area, heads hooking, no swing, track dries up too quickly, or no taper. How do you trouble-shoot your pattern and fine-tune it to get the ideal conditions for this year’s league? Here are some tips for common problems with patterns which should help you make proper adjustments.
Too Much Carrydown
Too much conditioner at the end of the pattern can cause excessive carrydown. This can be rectified by not loading as far down lane on the forward pass or increasing the machines buff out speed, which decreases the amount of conditioner on the lane towards the end of the pattern.
If your machine has our reverse brush drop feature, this is another fine tune adjustment you can make to bring the amount of conditioner farther back towards the foul line, or limit the amount of conditioner towards the end of the pattern. Poor cleaning can also cause carrydown issues. This can come from an incorrect mixture of cleaner or improper machine performance. It can never hurt to double check to make sure your machine is cleaning properly. To do this, perform a clean-only run on a few lanes and see if all the conditioner and cleaner are removed from each lane.
Back Ends Are Too Strong
Lengthen the pattern or create more taper to tone down the back end reaction. Tamer back ends provide predictable ball reaction and make spare shooting much easier.
Different types of cleaner provide different back end motions; this is another “condition” adjustment you can try. You could also experiment with a weaker ratio of cleaner to water mixture, but be careful; there is a fine line between getting the lane clean, and not clean enough.
Not Enough Hold Area
Make no mistake about it, as much as bowlers think they like swing area, what creates the highest scoring environment is hold area. The hold area is created by the amount of shape in the pattern towards the end as well as some friction outside of target. Without both, it is just about impossible to have the other.
If your lane machine has reverse oiling capabilities, starting the reverse oil loads farther down the lane will help increase hold without fear of getting too much conditioner at the end of the pattern, which as we said before, can cause carrydown issues.
Lane topography can increase hold area, a side slope away from the pocket at the break point area for instance, but topography can also minimize hold area if the side slope is towards the pocket at the break point area. Before you start searching for hold area by way of the oil pattern, get to know your lanes to make sure your lanes will allow the type of shot you are searching for.
Heads are “Hooking”
The amount of oil in the lay down area, or a lane surface in poor condition, can cause the heads to hook. In both instances, the lane machine should run slower in the heads, 10 or 14 inches per second on Kegel machines. The slower the machine travels, the more brush strokes per distance traveled which increases the amount of conditioner to any one area. This is better controlled on the return oil due to the direction of travel and the rotation of the buffer brush. Apply oil loads during the return travel that finish closer to the foul line (but not less than 4 feet).
Another thing that will give the perception that the heads are hooking is when the lay-down point of the bowling ball is on the upslope of severely depressed heads. No amount of oil in the world can fight a significant gravity influence towards the headpin in this situation.
No Swing Area
The amount of oil on the outside boards or adverse lane topography can affect swing area. Reducing the length of your oil pattern, or decreasing the amount of the applied oil on the outside boards, will increase the amount of swing area. But be cautious, even though bowlers like to swing the ball, your lanes just may not allow that to happen with the success you, and they, are looking for. Just know, however, our highest scoring patterns are the ones where most styles can go up the lane and have hold area.
A recent example is the 2011 WTBA Women's World Championship where many scoring records were set on the 47' Paris oil pattern. Note: the 2011 version of the Paris pattern tapes out at 4.2:1 at 22', so be aware if you try and use this in your Sport Bowling league.
Another example of a high scoring pattern is our Kegel Navigation Challenge pattern Route 66. This 45’ pattern routinely outscores many higher ratio shorter recreation patterns.
If you have topography issues, or side slopes that go towards the outside portion of the lane, the pattern should be adjusted by stacking up your inside oil line, applying conditioner farther towards the end on the forward and reverse passes, and allow the bowlers to play a more direct line to the pocket. This should create more area where ball reaction is concerned on a longer pattern.
Another topographic issue that can decrease swing area is depressed heads. Depressed heads cause the ball to quickly lose energy which makes down lane recovery (swing area) very difficult no matter how little oil you apply to the outside boards, or how much you apply to the heads.
Track Area Dries Up Too Quickly
Many bowling centers do not apply enough oil to the mid-lane track area on both the forward and return passes. Applying oil to the track on the return pass can help provide more longevity and stability without drastically affecting the forward oil readings and ball motion at the end of the oil pattern. Another adjustment is widening your pattern slightly. As balls hook more, the track area is becoming wider and farther down-lane. Take your middle loads and try widening them out a board or two and see if this adjustment gives you more longevity to your track area.
No Taper to My Pattern
The easiest way to create taper in the pattern is to make adjustments to your lane machine’s drive speeds during the forward pass only. Increasing the drive speeds on your forward run towards the end of the pattern will apply less oil in that area which increases front to back taper.
If your machine has Kegel's reverse brush drop capability, dropping the buffer brush farther back into the pattern on the reverse pass can also give you more front to back taper within your pattern.
Conclusion
With these tips, tricks, and troubleshooting techniques, you should be able to tweak your pattern and make it playable for most of your league bowlers. However, even with excellent lane conditions, you may still not be able to please everyone. If you reach the point where the majority of the bowlers are happy and bowling well, then it may be time to leave the lanes alone.
As always, it is important to remember that the pattern is not the only factor contributing to your lane conditions. You are competing against the lane topography, the other bowlers who share the lane, and Mother Nature herself. With topography, we cannot stress enough how important it is for you to know the shape of your lanes. When that information is known, finding that right oil pattern for your center is much easier. Without it, it's just a trial and error exercise.
Bowling is about skills and technique, but it is also about versatility and one’s ability to read the lanes and make adjustments to account for those factors which are out of your control.
Warning: Managing lane conditions may result in the loss of sanity. If it occurs, please contact our free Kegel Tech Support at (800) 280-2695 and we’ll help you get it back.
Oil Pattern Depletion
Oil pattern depletion (breakdown) is much different with today’s high flaring balls versus the low flaring balls of the past. Oil pattern depletion also happens much quicker and much more with today’s bowling balls.
When bowling balls had essentially balanced weight blocks, or differential Rg values of .010” or less, the ball basically rolled over the same place every revolution. When this happens, the ball picks up all the oil it can within the first couple revolutions and oil pattern depletion only happens in the head area, or only in the first 16’. The rest of the oil pattern remained intact, but not with today’s high differential Rg weight blocks.
Most bowling balls today have differential Rg values in the .040” to .060” range. The maximum differential Rg value is now .060”, according to USBC specifications. These high differential Rg values create a dynamic imbalance within the bowling ball. When a ball is drilled to maximize this imbalance, this causes track flare and results in the bowling ball rotating on a fresh part of the cover every revolution. This erases oil off of the lane every revolution, causing oil pattern depletion throughout the entire length of the oil pattern, instead of only the heads as when bowling balls were more dynamically balanced.
Kegel performs many tournaments every year and one of the things we are constantly measuring is oil pattern depletion. We do this because the main goal for the laneman in tournaments is to try and create a playing condition that has the best opportunity for fair play; in other words, give as many styles a chance as possible. If massive oil pattern change continues to make this task difficult, we need to find ways to help Lanemen do their job better.
How much oil is erased with today’s balls?
During a recent seminar tour, we got a group of bowlers’ together and measured oil depletion after 10 minutes of practice, and then every three games of play. At the end of this test, we had 9 games per lane. To put it in comparison, a 5 person team bowling a 3 game league has 15 games per lane.
To follow are the results of that test:
The greatest amount of depletion occurs during the early stages of play because the ball creates a larger footprint within the oil pattern. In the head area, there were 80 units of oil before bowling. After 9 games, there were about 35 units in that same head area. The move left by the players was not the lack of head oil; it was the ‘spark point’ being reached in the mid lane and the back part of the pattern causing the ball to hook more and forcing the players left.
Now we show why this massive depletion of the oil pattern can affect fair play. The following graphics are a comparison on how different styles of players break down oil patterns.
The event was the 2009 European Bowling Tour Masters featuring the top 16 players, men and women, from the 2008 European Bowling Tour point list. Both groups had 3 bowlers per pair and they played 8 games. So the lanes had 12 games per lane plus 10 minutes of practice on them. There was also an equal amount of lefties and righties on both the men’s side and the women’s side, and every player bowled on each pair of lanes twice within the block, so it was a very good comparison.
The fresh oil pattern was 44’ in length with the same pattern used for both the men and women. Below is the graphic of that pattern:
The first depletion example is the women’s side of the event. They were bowling by themselves and as with most lower rev players, because of the decreased motion on the back end, these type players tend to play in the same area on the lane and in a tighter line to the pocket.
As you can see in the above graphic, the women essentially started at the slope of the oil pattern, the rise from the least amount of conditioner to the greatest amount of conditioner, and broke the oil pattern down in a very logical manner. When oil patterns are broken down this way, scoring pace can increase greatly.
The men played on lanes right next to the women players. Here we had players like Jason Belmonte, Osku Palermaa, Dominic Barrett, and several Scandinavian players with fairly high rev rates. Below is the graphic of how the men broke that same fresh oil pattern down.
Because of the great amount of potential hook we have in the game today, and especially with the higher rev players, the slope of the oil pattern is not always followed as it used to be when bowling balls hooked less.
What is interesting, is the area where the bowling balls roll throughout the pattern, both groups depleted the same amount; over 60%. Testing has shown depletion is not significantly greater with higher rev rates, depletion is only more spread out. Towards the end of the pattern where all balls meet, both groups depleted the same amount, over 60%.
Here is the tape data and depletion percentages at comparable distances throughout the above patterns.
Most bowlers still believe “the heads” breakdown the most and therefore affect ball motion the greatest. This was the case with balls that did not flare, but that’s not the case with balls that flare.
When flaring balls are rolled over an oil pattern, the oil pattern is erased near the same amount,percentage wise, from the lay down point to when the ball exits the end of the oil pattern. The most oil is depleted where the footprint is the greatest, but at each distance, the percentage of depletion is essentially the same.
Once the oil pattern is depleted enough for the ball to reach the “spark point” in the mid lane and back part of the pattern, players start moving inside. And they move until the modern practice of lofting the gutter cap comes into play.
If depletion continues to happen at such a rapid rate, lofting could become the modern way to play the game. After all, we have yet to see a ball hook while it is in the air.
Earl Anthony - Simply the Best
THE difference between the good players, the very good players, and the great players, is the mental game. But what exactly is this mysterious thing called the "mental game”?
Many of the good players and very good players possess similar physical talents to the great players, but they often fall short with their accomplishments.
Simply put, the physical game - in any sport - is how the athlete performs based on their overall talent, ability, potential, skills, and preparation. The mental game however is a totally different animal. This element of the "package" is HOW the athlete thinks.
We have all heard about how the great players are the ones who work the hardest. They are the first ones to practice, and the last ones to leave. But, there is a lot more to it than that. Desire, dedication, determination, self-control, focus, concentration, confidence, self-esteem, positive thinking, goals, visualization, knowledge, and a host of other things, must be mastered.
The following is how the late great Earl Anthony “mastered” the game of bowling.
One time Earl Anthony was being interviewed after one of his early victories by a reporter. It was in the early 1970's, and the reporter wanted to be controversial about the lefty-righty situation that had run rampant in the late 1960's. He said to Earl, "This victory establishes you as one of the best lefties on Tour. Are you happy with that assessment?" Earl looked him right in the eye and said, "I don't know anything about that, my goal is to be the best bowler."
There was another time I remember that showed exactly how the man thought. It was 1974 and he had just been named the Bowler of the Year. A press party was arranged and the award was being presented to him in his office. The wall was cleared and the photographer was going to take a picture of Earl putting up the plaque. Earl was standing toward the corner of the wall with the plaque, and someone in the crowd told him to “put the plaque in the center of the wall.” Earl replied, “No, this one is going here, and the rest of them will go across the wall.”
Earl was right, the other Five Bowler of the Year Awards eventually filled up the entire wall.
Previously, I had written a series of books called the “Final Phase”. They were instructional books to help bowlers learn about the great sport of bowling.
For one of these books I interviewed Earl and posed this question this question to him; "Earl, in my opinion, you were the greatest bowler in the world. You totally dominated the PBA Tour for more than ten years. What do you feel was the formula-for-success that you enjoyed?”
Earl’s answer was, "In my opinion, success is the result of hard work, dedication, intelligence, selfishness, and some luck. How hard you work, and how much you are willing to sacrifice to achieve your goals, will determine to a great degree your level of success.
Natural talent is a wonderful gift, and to be the very best you must have a lot of God-given talent. However, you must work hard to develop that talent.”
Earl continued on to say, “To be a winner also takes a strong mind. You must be able to focus your concentration level to a fine point, and achieve a level of confidence in your ability that is unshakable under the most extreme pressure. Most winners develop an air of arrogance, which is a by-product of the confidence that they have in their ability.
The reason I was successful, was my ability to understand and develop my mental game, as well as the endless hours of practice on my physical game. There was also a certain amount of fear-of-failure that was tempered by a small degree of courage that I used as a motivator to let me continue to fight for my goals, despite many setbacks, and a willingness to put bowling, and my desire to be the very best, above all other things in my life."
Those three interviews alone, tells you volumes about why I thought Earl was the very best. To this day I still get chills and goose bumps when I read them.
Dual Oil Patterns are here! What’s next?
The European Bowling Tour has recently announced it will have two tournaments in the 2009 schedule where players will compete on dual oil patterns. Following the lead of Ronald Dol and Luc Jensen, organizers of the EBT Hammer Bronzen Schietspoel Tournament which will use dual oil patterns for the third year in a row, the Brunswick Aalborg International will also be contested on dual oil patterns for the second straight year.
Although dual oil patterns have been a mainstay of international championship competition for the last several years, most other high level singles events still use a single oil pattern, but times are changing.
Even the 2008-09 PBA Tour season is testing the waters with an event that utilizes six different oil patterns and another event will employ dual oil patterns on each pair during the PBA Match Play Championship in Norwich, CT.
The format of the recently concluded PBA National Bowling Stadium Championship followed past Foundation Games, the WTBA World Ranking Masters, the EBT Masters and the ETBF European Champions Cup.
In all those events, one qualifying block is played on a short oil pattern and the other qualifying block is played on a long oil pattern. During the match play rounds, all games are played on pairs where every left lane is conditioned with the long oil pattern and every right lane conditioned with the short oil pattern.
How did this all come about?
There are two major reasons why dual oil patterns came into existence. One seemingly clear but not so obvious reason is the technological advancement of the modern lane machine. In the not so distant past, conditioning bowling lanes was done by hand or by machines that could only condition the lane. The challenge however was the time consuming cleaning of bowling lanes. Today’s combination lane machines can consistently condition and clean a bowling lane in less than two minutes making it possible for dual oil pattern events to become a reality.
The other and most significant reason is a group of people came together with a vision and were not afraid to depart from status quo. In the year 2000, then WTBA President PS Nathan called for a World Symposium in Malaysia to address many of the perceived problems related to the sport of bowling.
Out of that symposium, which included the likes of Sid Allen, Tom Kouros, John Davis, Len Nicholson, the late Bill Wasserberger along with other highly respected people in bowling, the WTBA Technical Committee concluded “that a single oil pattern format was unfair, since it overly favored a particular style of play regardless of how the lane was oiled.”
During that same symposium, the WTBA Technical Committee also felt the question of “who is the best bowler” needed to be examined further. Through much discussion and digging deeper into the question, the WTBA defined what they feel are the most important traits that should make up a World Class bowler.
The committee agreed to and created the synonym V-PARK which stands for; Versatility, Power, Accuracy, Repeatability and Knowledge. There was one trait however that was at the very top of every members list, Versatility.
The Technical Committee felt that “the ability to bowl over a wide range of conditions elevated a player from one of quality to that of greatness” and therefore led to the conclusion “that WTBA’s present oiling procedures were not conducive to identifying and rewarding great players, but instead only identified specialists.”
Then committee member Craig Woodhouse suggested the concept of multiple oil patterns and it was unanimously agreed that this would be the standard for all future World Championships.
From where does it go from here?
There is no question that every winner of a dual oil pattern event has garnered the respect of their peers for that week’s competition. It would be reaching pretty far for anybody to say “so-and-so” only won because “they matched up” to both oil patterns. In that regard, the WTBA Technical Committee’s vision about versatility held true but that doesn’t mean dual oil patterns doesn’t have it detractors.
There is no debating the fact that airlines have decreased the allowable weight limits and travel by way of air has been a challenge for the modern bowler. Automobile travel has even been impacted by the modern game and the number of bowling balls competitors need, or feel like they need, to travel to any one tournament even in single oil pattern events.
So one can only imagine that one of the more common negatives of these dual oil pattern events is the perception that the players need to travel to tournaments with an increased amount of equipment to combat this extra oil pattern.
Although dual oil pattern events solely utilizing very long and very short oil patterns actually limit the number of ball choices because optimal ball motions are very similar and the best line is normally very defined, as tournaments move towards dual oil patterns in the medium distance range, that perceived issue will most likely become more reality than perception. When competitive oil patterns are in the medium distance range, all the other variables that make up the playing field come into play more and optimum ball motion becomes an unknown until a player is onsite.
Another remarkable trend in the competitive bowling world the last few years is tournaments being organized and played with severely limited equipment rules or utilizing less frictional bowling balls. The 2005-2007 Dutch DVA Open, the 2006 WTBA World Challenge, the 1997 Scandinavian Plastic Only tournament and multiple Foundation Game events have been held with strict equipment limitations. Some events allowed only one ball while others allowed only one type of ball.
In the Scandinavian Plastic Only event, organizer Ulf Hämnäs stated that “many players in the region had the perception that the higher level players were the best because of their unlimited access to high tech equipment.”
Once the results were tallied however, those same high level players not only still finished at the top of the leader board, they far outpaced the field. Hämnäs said “the equipment advantage perception was replaced with the surprise that the amount of time spent on the lanes practicing actually made the difference, not just getting new balls.”
Hämnäs further stated, “I think this was the time when a lot of bowlers actually understood the greatness of bowlers like Tomas Leandersson.”
So did the winner “match up” best in these events? Much like the 1997 Scandinavian Plastic ball event, according to the other organizers the winners of their events received the same accolades from the competitors as the dual oil pattern event winners, respect from their peers for a job well done. The overall feelings were it was not that the winner matched up the best; it was that the winner bowled the best.
Now in the year 2009, even the PBA Tour is going to hold an event using only one type of bowling ball, the 50th Anniversary PBA plastic ball. In this historic PBA Tour event, all competitors will be limited to two of the special 50th Anniversary plastic balls for the entire event. The main idea is to level the playing field by taking the perceptual equipment advantage, or disadvantage, away so success is determined solely by a player’s physical and mental skill.
In other words, the event goal is to “ensure that the abilities of the athlete, first and foremost, will determine the outcome of the competition.”
Sound familiar?
Water Walker
I think that in order to give this story as much credibility as possible, I am going to have to brag a little. I have been involved in doing the lanes with the PBA for over 800 tournaments, which included the National Tour, the Senior Tour and all seven Regions of the Regional Program. I am the only person who has done lanes for every bowler that is in the PBA Hall of Fame. In other words, I have seen them all. And, perhaps, I am really the only person who knows exactly what they bowled "on", as far as lane conditions go.
My personal All-Time Top-10, includes; Dick 'Water Walker' Ritger. You talk about TALENT. Dick was unbelievable. He was a world-class bowler, a world class guy, and later became a world-class coach. Without question he was one of the coolest, smartest, shot-makers in the history of our great sport. He could bowl on anything.
I have literally hundreds of stories of some of the tremendous feats that were performed by the greatest bowlers in the world; those that are in the PBA Hall of Fame.
This particular story took place in the early 70's. We (the Tour) were at Cranston Bowl in Cranston, Rhode Island. The weather was absolutely miserable as it had been snowing for about a week before we got there. It was 10-degrees outside when I got off the plane. Not only that, but my job as laneman was going to be a lot tougher this week because we knew in advance that the place was in bad condition because they hadn't resurfaced in a couple of years and all of the league bowlers had been complaining. And it was an old, drafty two-sided house and each side played drastically different from each other - as well as each pair playing differently from each other. I knew that I was going to hear about that.
After the first day of qualifying, Ritger was in the lead, which wasn't unusual for this 20-time champion (at the time). Almost every bowler was upset with the lanes and I had to hear about it.
That night at 2:00am I went in to do the lanes and it was now 19-below zero. There was so much snow in the motel parking lot, that and I couldn't find my car and had to walk about a mile to get to the bowl. About 15-minutes after getting there, part of the roof on the high-side (the real tough side) caved-in from the weight of the snow. It was a disaster. The janitor called the head mechanic who in turn called the Manager. He called everybody he knew to get in there to help clean up the mess. I called Harry Golden (the Tournament Director) to let him know what had happened. I cleaned and oiled the low-side then went over to take a look at what was going on over on the disaster side. There were about 20 people cleaning the water, snow, ceiling tiles and other debris off of the lanes and approaches. You could see the sky through the hole in the ceiling. I remember thinking: "I'm sure that the guys will blame me for this, too."
There were buckets on the lanes that were still catching water from the drippy roof. It was now 6:00am and the Pro's were scheduled to bowl at 9:00am. At that point I thought that there was no way. I started cleaning and oiling the part of that side that wasn't under water. When I got to the part of the house that had caved in, a "Miracle" happened. It had stopped raining and the dripping over the lanes had stopped. I cleaned and oiled the rest of the lanes. There were still some drips coming down over the lanes, but "Miracle number 2" was that the drips were only over the gutter gaps and the buckets that were placed there were catching all of the drops. It was about 8:45am now, and I took the lane machine to the back. The mechanic and all his helpers were back there huddled next to a little heater he had, and they were all trying to dry out.
When I came out of the backend, I saw about 20-bowlers standing in the settee on 31 and 32. I went over there to see what was going on. The only drips that were still coming down were over the approach on that pair and because of the full field, they had to use that pair in the tournament. Harry made the decision to leave the three buckets where they were on the approach. It was either that, or put 5 on a pair, and none of the bowlers wanted that. The buckets were to stay in place for BOTH squads.
I stayed around to watch the 1st squad bowl. After they bowled their 6-games that morning, the high game on the pair was 149. It was impossible for the players to walk around the buckets that were there to execute any type of normal shot.
Now the next squad came in to bowl. Ritger was scheduled to bowl his 2nd game on 31 and 32. It would be interesting to see what he could do there and not lose too much of the lead that he had enjoyed. When he got there for game 2 of this second day, there was a huge crowd in the bleachers, and standing behind the bleachers, as well.
I watched him (with no practice balls) alter his approach by snaking his footwork around the three buckets in a serpentine manner. I couldn't believe my eyes. He shot 279 like it was nothing. It was ridiculous.
One World - One Game
It has been almost ten years since John Davis (Founder of the Kegel Company), called together a group of experienced lane men in an attempt to further research the on-going lane conditioning problems with our Sport. It had become apparent that too many tournaments were deemed unfair by the participants and tournament organizers. Bowling ball technology had rapidly advanced and it was getting next to impossible for the lane man to do the job without some sort of social controversy. After that five day meeting in Sebring, Florida, Davis promised to undertake the huge task of taking care of lanes at every major tournament in the world and then posting those results on The Foundation website for the whole world to see. Davis and The Foundation came up with their initial slogan which was: “One World – One Game.”
The Foundation also coined two other phrases:
1. "You don't need to be a lane man to know that there are problems, you just need to be a lane man to know how bad the problems are."
2. "If not us, who? If not now, when?"
Early on, a series of scratch tournaments were developed, called: The Foundation Games. These events were held in this country (and abroad) with some promising results. They were unique by featuring ‘multiple conditions’ in an attempt to further challenge the participants by having more than one lane condition to compete on. Challenging oil patterns were used (both long and short) that required the athletes to compete on different lengths of oil during competition.
In 2000, Dr. P.S. Nathan, then President of the World Tenpin Bowling Association (WTBA), held a World Bowling Seminar in Malaysia and Davis was invited to attend along with many other bowling leaders from around the world. At that week-long educational meeting, it was unanimously decided that in order to find out who the best players were at any given event, the athletes needed to be challenged with these ‘multiple condition’ type tournaments.
The WTBA then formed a Technical Committee (TC) to continue researching the problems on a world wide basis. Since then, different tournament formats have been tested along with bowling ball restrictions (amount of balls used in the events) which were instituted. It is quite clear today, that some of the underdeveloped countries are at a disadvantage regarding bowling equipment.
For many years now, numerous thoughts, opinions and feelings about lane conditioning have been constantly expressed on most every bowling websites discussion groups. Depending on the average person’s position (agenda), most blame the problems with our game on various aspects of the game, including; pins, oil patterns, balls, kick-backs, flat gutters and an assortment of other things. Most have never done lanes and have no idea what that particular job entails.
Today, even with the use of different formats and multiple conditions, problems still exist in our great sport. The WTBA Technical Committee feels that it is time to try a different approach.
"One World - One Game - One Ball"
In 2003, Davis was named as Chairman of the WTBA TC, and Kegel was still taking care of all the tournaments for the WTBA and developing countless oil patterns. It became obvious that the lane man still could not do his job without some social unrest. Something else was needed.
The WTBA TC decided to research and test a type of bowling ball that would not mutate the oil patterns as much as today’s High Tech balls do. Davis was put in charge of doing the research for this project. Days, weeks and months went into this very technical testing, using CATS data.
A ‘prototype’ bowling ball was developed which showed encouraging results. During the week of April 17-22, a Bowling Writers meeting was scheduled in Orlando, Florida (which is only about 80 miles from Kegel’s Training Center), that was combined with the USBC Annual Meeting.
The WTBA TC also scheduled a meeting at this time and this was a chance to announce this new theory. A small scratch tournament would be held and the results would be shown to the world. Many top players from Florida would participate along with some other top amateurs and former PBA Tour champions. It was an eight game event that was bowled across eight lanes. The amount of oil that was used was 7.140 mL, which is an amount that was used in the early 1970’s.
Those results (total pin fall) were:
1. Bob Learn, Jr. (1880)
2. Vernon Peterson (1770)
3. Matt Gilman (1715)
4. Bob Handley (1675)
5. Mike Purdy (1671)
6. Larry Barwick (1670)
7. Rob Comito (1666)
8. Steve Johnson (1660)
9. Neil Stremmel (1655)
10. Storm DeVincent (1627)
10. (T) Sami Luoto (1627)
12. Chris Chartrand (1612)
13. Dennis Davis (1598)
14. Craig Auerbach (1596)
15. Saul Insignares (1573)
16. Tony Lavance (1572)
17. Ron Dixon (1523)
18. Jose Rodriquez (1514)
19. John Forst (1513)
20. Dennis Psaropoulos (1512)
21.Tony Crews (1477)
22. Bill Blackwell (1454)
23. Pekka Korpi (1383)
24. Josh Moore (1354)
Each player paid a $100.00 entry fee to enter the tournament, and that included a bowling ball. Each player had a choice of 15 or 16 pounds to use. Except for that weight difference, all of the balls were made as similarly as humanly possible. Davis donated an additional $2600.00 for a total Prize Fund of: $5000.00. Learn earned $2000.00 for the win along with a very nice banner that was signed by all of the participants and those on the WTBA TC. In all, 12 players cashed.
When asked if he wanted the banner, Learn said, “Certainly. It will go in my trophy room with all of my other cherished awards.” He added, “This was great. ALL tournaments should be like this one because I really think that it was the fairest tournament that I have ever bowled in.”
After the event, all the players were asked to fill out a detailed questionnaire that had a multitude of pertinent questions regarding the tournament. Those queries are currently being analyzed.
All in all, it was deemed a tremendous success by the Players and Officials. All results of the CATS data (from every shot, from every player) are also being analyzed. When completed, a detailed report will be sent to WTBA President Heikke Sarso for review.
STAY TUNED!